Αριθμός ανταλλακτικού
Αποστρατιωτικοποίηση
Διάρκεια ζωής
UOM
NIIN
Αριθμός ανταλλακτικού:
272t8089031
Αποστρατιωτικοποίηση:
Yes - DEMIL/MLI
Πληροφορίες ανταλλακτικού
Helicoils for two 8-32 headless set screws for breaking bond w/aircraft
NSN
Εθνικός αριθμός αποθέματος:
Κωδικός ονόματος στοιχείου:
00749
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
10.875 inches
MRC:
The distance measured in a straight line from the bottom to the top of an item.ABKW
Overall Height:
1.417 feet
MRC:
An overall measurement taken at right angles to the length of an item,in distinction from thickness.ABMK
Overall Width:
2.780 inches
MRC:
The length of a straight line which passes through the center of a mounting hole,and terminates at the circumference.ABTB
Mounting Hole Diameter:
0.257 inches
MRC:
The number of mounting holes provided.ABTJ
Mounting Hole Quantity:
12
MRC:
The number of complete cyclic changes,per unit of time,for which an item is rated.ACZB
Frequency Rating:
116.000 megahertz single antenna element and 156.000 megahertz single antenna element
MRC:
The distance between mounting facility centers.AEJN
Distance Between Mounting Facility Centers:
1.280 inches and 1.640 inches and 1.560 inches and 1.840 inches and 3.000 inches and 1.000 inches and 2.000 inches and 3.000 inches and 0.860 inches
MRC:
The minimum and maximum limits of temperature at which the item is rated for operation.AFGA
Operating Tempurature Range:
-62.0/+71.0 degrees celsius
MRC:
A letter or group of letters used to designate the particular coaxial connector series.AHUC
Coaxial Connector Series Designation:
C single antenna element
MRC:
The design of the connector end.AHUD
Connector End Design:
Socket single antenna element
MRC:
The orientation of the electrical vector of energy radiated from the item relative to the line of propagation.AJCT
Electromagnetic Polarization Type:
Vertical single antenna element and horizontal single antenna element
MRC:
The graphical representation of the radiation pattern of the device as a function of direction.AJCU
Radiation Pattern:
Omnidirectional single antenna element
MRC:
The reactance-resistance complex value which must be matched by the transmission line and termination to achieve lowest standing wave ratio,expressed in ohms.AJDD
Characteristic Impedance In Ohms:
50.0 single antenna element
MRC:
The means used to direct a beam/s/ of energy successively over a given region.AJDH
Beam Scanning Method:
Rotating single antenna element
MRC:
Indicates the type of device used to effect positioning or to vary positions (as in scanning) of the item.AJDJ
Positioning Device Type:
Drive motor single antenna element
MRC:
The voltage rating at which the item is designed to operate,expressed in volts.AKRE
Voltage Rating In Volts:
115.0 ac single antenna element and 25.0 dc single antenna element
MRC:
Indicates the design type of the item.APGF
Design Type:
Blade single antenna element
MRC:
The means of attaching the item.AXGY
Mounting Method:
Bracket
MRC:
Indicates the type of terminal for providing electrical connection to the item.CSCF
Terminal Type:
Connector, receptacle single antenna element
MRC:
The angle between two opposite half-power (three decibel (3 db)) points of the beam.CTLS
Beam Width Angle:
30.0 degrees horizontal single antenna element and 30.0 degrees vertical single antenna element
MRC:
The ratio of the signal intensity of an item radiated in a specific direction to the signal intensity radiated in the same direction by a standard device,expressed in decibels.CTMN
Power Gain In Decibels:
0.80 single antenna element
MRC:
The specification,standard,drawing,or similar instrument that specifies environmental and performance requirements or test conditions under which an item is tested and establishes acceptable limits within which the item must conform identified by an alphabetic and/or numeric reference number. includes the commercial and government entity (cage) code of the entity controlling the instrument.TEST
Test Data Document:
85226-dc-50-1 drawing (this is the basic governing drawing, such as a contractor drawing, original equipment manufacturer drawing, etc.; excludes any specification, standard or other document that may be referenced in a basic governing drawing)
